10 Myths Your Boss Has About Repairs To Upvc Windows

Repairs to uPVC Windows

uPVC windows are an excellent option for modern homes. They are easy to maintain and durable, as well as long-lasting. Unlike timber and aluminium, they are not susceptible to rust or rot.

It is important to clean and oil UPVC doors and windows on a regular basis. This will reduce unnecessary repair costs and also improve energy efficiency.

1. Broken Glass

The damaged glass in your windows could cause significant damage to your home and even be fatal. It is crucial to take the time to ensure that you're doing everything you can to ensure that your windows are in good condition.

Single-pane windows are fairly simple to replace and typically fit into frames that were previously in use very easily. If you have double-paned windows which are joined by internal beading, it is difficult to remove and replace the old panes. In this instance it is essential to purchase plastic spacers in order to aid in fitting the new pane into the window frame.

If you are going to try to remove the window panes by yourself, it is essential to wear the proper safety gear such as gloves that are thick and protective eyewear. You should also lay down a dropcloth before you begin working on the window panes, so that any shards of glass fall onto the fabric and not onto the floor and could be trampled under.

It's a good idea to seal the gap after the glass has been removed. This will keep drafts and water from getting into your property until a professional comes out to repair the window. It also acts as a barrier to prevent any intruders from making their way into your home. If the gap between the door and the window is significant, you may prefer a security screen that also includes a window. This will provide the best of both.

2. Sagging

Upvc windows and doors are a cost-effective energy efficient, durable and Window Repair long-lasting alternative to timber windows with sash. As time passes, they may develop a number of problems that include sliding. A sagging uPVC window can cause problems with light, draughts and even security. If you find that your uPVC window is beginning to shrink, it's crucial to act fast to stop the issue from getting worse.

Repositioning the hinges can aid in fixing a window that is sagging. You'll first need to open the windows so you can get at the frame. Then, remove both the top and bottom hinges using a screwdriver and adjust them counter-clockwise or clockwise. Close your window to test the fit after you've repositioned your hinges. If you're satisfied with the fit, tighten the screws until they remain in place.

If you are unable to move the hinges, you may have to replace the seal. Over time rubber seals can lose their elasticity and dry out which causes them to lose tightness. If this happens, it's important to replace the seal as fast as possible to ensure your uPVC windows are waterproof and safe from drafts.

uPVC handles may also loosen. Often this is due to screws that have become loose over time. However, window Repair it can be due to the fact that the handle mechanism has been worn out. It's relatively simple to fix a loose uPVC hand. First, you'll need close your window and do an experiment to ensure that it fits. The corner joints of the sash must align with the casing joint. If it doesn't then you can use a screwdriver to loosen the handle and then turn the mechanism back into position.

3. Water Leaks

If you wake up to damp floors and mouldy walls every time it rains it's crucial to take action. Water leaks through windows can cause structural damage to your home and also affect your ability to regulate the temperature of your home. Most of the time, uPVC window leaks are caused by a lack or damage to the sealant.

This is an easy fix that can be completed by any DIYer who is competent. Based on the severity of the problem the caulking that was used up may need to be removed before a new layer is applied. It is crucial to remember that when it comes to uPVC window repairs, you should avoid the temptation to "over-caulk in order to make the area harder to clean and could reduce the efficiency of your energy.

Check that any drainage holes have no debris in them and ensure that the sill pan has been properly angled to allow the water to drain from the window. In more serious instances, you might have to consider replacing the window.

Mold spots and rotten sills are other signs of water leakage. The fungus thrives in conditions of dampness and can spread quickly throughout the home.

It is also important to note that if the leakage originates from the glass in your double glazed windows, it's more likely to be an issue with the glass seal, rather than the frame or sliding. A uPVC specialist can easily fix this issue by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

If your uPVC windows are difficult to open, or are loose and open with a breeze, it may be hinges that are at fault. They can be easily repaired by any skilled DIYer and are usually done within a few minutes.

Like all mechanical parts hinges are prone to be damaged over time. It is essentially a very simple procedure, but it is easier with someone else to help you hold the frame in place.

It is also worth checking that the uPVC hinges are being opened and closed in the correct direction. Check for the arrows on each hinge to determine which way the window should be opened.

The issue could be caused due to opening the window in the wrong way or a faulty installation at the factory. This can often be resolved by sending us a photograph on our website. We will be pleased to offer you suggestions.

Regularly lubricating the hinges is essential. This can be done by applying a light engineering oil on the hinges. We suggest using a solvent-free lubricant such as 3-in-one Multi-Purpose Oil. Regular lubrication can make the window easier to open and close. It can also reduce the chance of windows getting stuck and stop corrosion. This should be done at least once a year. WD40 and other solvent-based lubricants should not be used as they could damage your uPVC windows.

5. Draughts

Draughts can be caused by several different causes. First, the hinges because of wear and tear, may become displaced, which can cause an opening to appear where the sash meets the frame. If they're beyond repair, it could be necessary to get them re-aligned. The interlock, which is on the hinge side of the window, may also become misaligned, again it is feasible to give them a good clean, but in certain cases, it may be necessary to have these replaced.

The next common reason for draughts is window seals. They are prone to wear or damaged over time, and will allow air to escape through the gaps. This can be avoided by replacing them with high-quality weatherstripping. Another alternative is to replace the window with low-emissivity glass, this will help to regulate indoor temperatures and again will lessen the possibility of draughts.

The final method to cut down on the amount of draughts is to use a Draught-exclusion device. These are typically fabric tubes filled with a filler that can be put on top of your window Repair sill. They can keep your home warm by blocking out cold air.

With a bit of regular maintenance and repair your windows made of upvc will continue to provide a great level of insulation and security for your home. However, it is important to recognize that windows last for a certain period of time and there may come the point when it's more cost-effective to replace them rather than fix them. So, if you're experiencing problems with your upvc windows, it's recommended to seek assistance from a professional immediately.