17 Reasons Not To Beware Of Repairs To Upvc Windows

Repairs to uPVC Windows

uPVC windows are a great option for modern homes. They are long-lasting, durable and easy to maintain. They don't rot or rust like aluminum or timber.

Regularly cleaning and lubricating UPVC windows and doors is essential. This will reduce unnecessary repair costs and also improve energy efficiency.

1. Broken Glass

The damaged glass in your windows can cause serious damage to your home, and could even be fatal. You should take the time to ensure that your windows are in good shape.

For single pane windows, upvc Window repair it is relatively easy to replace them, and the replacement will usually fit inside the frame of the previous one easily. However when you have double-pane windows that are secured by internal beading it will be more difficult to get rid of the existing panes and install new ones. In this situation, you will need to find some plastic spacers that help the new pane to fit correctly into the frame of the window.

If you plan attempt to remove the window panes by yourself, it is essential to wear appropriate safety gear that includes gloves with a thick layer of material and protective eyewear. It is also recommended to lay down a dropcloth before you start working on the glass to ensure that any shards will fall onto the cloth instead of landing on the floor where they can be trampled upon and cause further damage.

Once the glass is removed, it's a good idea to cover the gap with packaging tape or duct tape to prevent water and drafts from entering the home until a professional is able to come out and fix the window. It also acts as an obstacle to stop intruders from getting into your home. If the gap is large, you might think about an alarm door that comes with an integrated window as it offers the best of both worlds.

2. Sagging

uPVC is a durable, energy-efficient and affordable alternative to timber sash windows. However, over time, they are susceptible to a range of problems including sagging. A window that isn't properly aligned can cause problems with light, draughts, and even security. If you notice that your uPVC window is beginning to shrink, it's crucial to act fast to stop the issue from becoming worse.

Repositioning the hinges could help fix a window that is sliding. To do this, you'll need to open the window to access the frame. Then, you can remove the hinges on the top and bottom with a screwdriver and adjust them counter-clockwise or clockwise. Close your window to test the fit after you've repositioned your hinges. If you're satisfied with the fit of your window, you can tighten screws to hold them in the right position.

If you cannot reposition the hinges, you could need to replace the seal. Rubber seals can dry out and lose their elasticity with time, leading them to loosen. If this happens, it's crucial to replace the seal as quickly as possible so that your uPVC windows are waterproof and secure from draughts.

uPVC handles can also loosen up. This is typically caused by screws that have become undone over time, but it could also be caused by the handle mechanism getting worn out. Fortunately, it's easy to repair the loose uPVC window repairs near me handle yourself. First, you'll need close your window and do an initial test fit. The corner joints of the sash should align with the casing joint. If it doesn't, you can use a screwdriver to loosen the handle and reverse the mechanism back into the position it was in.

3. Water Leaks

It is essential to take action if get up each morning to discover mouldy walls and floors that are wet. Leaks of water from windows can cause structural damage to your home and also affect your ability to regulate the temperature in your home. Most often, uPVC window leaks are caused by damaged or missing sealant.

It is a fairly easy fix that can be completed by any skilled DIYer. Depending on how serious the issue is, old caulking might need to be removed. It is essential to keep in mind that when it comes to uPVC window repairs, do avoid the temptation to "over-caulk in order to make the area more difficult to clean and reduce the efficiency of your energy.

It is essential to ensure that any drainage holes are clear of debris and that the sill pan is angled in a way that allows it to drain away from the window. In more severe situations, you may have to replace the window.

Moldy sills and rotten ones are also signs of water leakage. This fungus thrives under humid conditions and can propagate quickly throughout the home.

It is also important to note that if the leak originates from the glass of your double glazed windows, it's more likely to be a problem with the glass seal rather than the frame or sliding. A uPVC specialist can fix this problem by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

If your uPVC windows are brittle to open, or slack and blow open with ease It could be the hinges that are at the fault. These are easily replaced by any competent DIYer and are usually completed in just a few minutes.

Nearly every home in the UK will have top-hung or side hung uPVC windows that use hinges and, just like any mechanical component they will wear out over time. The process of replacing a hinge on a window is an easy procedure, but it is easier if you have someone to assist in holding the frame in place.

It is also worth checking that the uPVC hinges are opened and closed in the correct direction. This can be done by looking for the arrow on each hinge. This indicates the direction in which the window should be opened.

The problem with the hinges on windows could be the result of incorrectly opening the window a certain way or due to inadequate installation at the factory. It is usually possible to fix the issue by sending us a photograph through our website and we will be happy to give you suggestions.

Regularly lubricating the hinges is essential. Applying a light engineering lubricant on the hinges is a good way to do this. We suggest using a lubricant that does not contain solvents, like 3-in-1 Multi-Purpose oil. Regular lubrication can make the window easier to open and close. It can also prevent corrosion and reduce the risk of sticking. This should be done at least every year. WD40 and other solvent-based lubricants should not be used as they can cause damage to your uPVC windows.

5. Draughts

Draughts in Upvc windows can be caused by different things. Firstly the hinges, again because of wear and tear, may become displaced, which will cause a gap to form where the sash meets the frame. These can be easily repaired by giving them good clean, but when they're beyond repair, it could be necessary to get them realigned or replaced. Second, the interlock can be unbalanced. It is located on the hinge's side and could require to be cleaned. In certain instances it is possible to replace them.

The next most common reason for draughts is window seals, these are susceptible to being worn out or damaged over time and allow air to escape through these gaps. This can be prevented by replacing them with high-quality weatherstripping. Another alternative is to replace the upvc window with glass that is low-emissivity, this will help in regulating indoor temperatures, and also lessen the possibility of draughts.

One of the most effective methods to reduce draughts is by using a draught excluder. These are usually fabric tubes filled with some type of filler. They can be put on the top of your windowsill. These will keep your home warm by blocking out cold air.

With a little regular maintenance and repairs your windows made of upvc will continue to provide an excellent level of security and insulation for your home. It is essential to remember that all windows eventually wear out and it is more cost-effective to simply replace them instead of fixing them. If you have any problems with your upvc Window repair window you should consult a professional as soon as possible.